Term
| What is not a requirement for the SMAW process? |
|
Definition
|
|
Term
| what is and incorrect statement about an E7018 electrode? |
|
Definition
| They are suitable for flat position and horizontal fillet only |
|
|
Term
| The distance from the molten tip of the SMAW electrode to the surface of the molten weld pool schould be |
|
Definition
|
|
Term
| Which of the following electrodes is not suitable for use in all positions? |
|
Definition
|
|
Term
| Which if the following electrodes would you select to produce a weld with shallow penetration? |
|
Definition
|
|
Term
| An engine- driven generator without a rectifier produces what form of welding current? |
|
Definition
|
|
Term
| Which group of electrodes is low hydrogen type? |
|
Definition
|
|
Term
|
Definition
| magnetic forces associated with direct current |
|
|
Term
| Duty cylce is a term used to indicate the...? |
|
Definition
| Percentage of time in a 24 hour cycle that a machine can operate at rated output |
|
|
Term
| When the welding machine is set to DCEP, cutrrent flows? |
|
Definition
| from the work to the electrode |
|
|
Term
| Which of the following welding cable sizes is the largest? |
|
Definition
|
|
Term
| Rectifiers are noted for their ability to..? |
|
Definition
|
|
Term
| in north america, alternating current changes direction... |
|
Definition
|
|
Term
| In order to reduce waste and control cost, you should weld until the electrode is |
|
Definition
| down to the classification numbers |
|
|
Term
| The last digit in the electrode classification E7018 idicates. |
|
Definition
| Type of current and electrode coating |
|
|
Term
| THe E7024 electrode can be used in |
|
Definition
| flat positon and horizontal fillets only |
|
|
Term
| The electrode classification that indicates a deep penetrating electrode that can be used with alternating current (AC) current is |
|
Definition
|
|
Term
| Back-steeping at the end of a weld made with the SMAW process |
|
Definition
| help to prevent crater cracking |
|
|
Term
| the first two digits of the electrode classification indicate the... |
|
Definition
| minimum tensile strength of the deposited weld. |
|
|
Term
| An E6010 deep penetrating electrode belongs to |
|
Definition
|
|
Term
| In GMAW, the shielding for the molten matal is accomplished through the use of.. |
|
Definition
|
|
Term
| GMAW us the abbreviation for |
|
Definition
|
|
Term
| In GMAW, isufficiant gas flow can cause? |
|
Definition
|
|
Term
| A warn contact tube results in... |
|
Definition
|
|
Term
| The benefit of copper coated electrode wires is |
|
Definition
| better arc starts, increases contact tip life, improved wire feeding |
|
|
Term
| What type of power source is used for GMAW? |
|
Definition
|
|
Term
| In GMAW, which type of metal transfer is restricted to a flat position and horizontal. |
|
Definition
|
|
Term
| What type of electrode wire is used with GMAW? |
|
Definition
|
|
Term
| in GMAW, the amperage is controlled by adjusting the |
|
Definition
|
|
Term
| in gas metal arc welding, electrode extension is defined as the distance from the.. |
|
Definition
| end of the contact tube to the tip of the wire |
|
|
Term
| Which AWS electrode classification is correct for GMAW wire? |
|
Definition
|
|
Term
| Which of the following is considered an advantage of the GMAW process? |
|
Definition
| Higher deposition rates than manual processes, easy to use comapared to manual processes, Less electrode waste then with SMAW. |
|
|
Term
| ELectric current is transferred to the electrode through the... |
|
Definition
|
|
Term
| what shielding gas or gas mixture with not produce spray transfer? |
|
Definition
|
|
Term
| The contact tube should be? |
|
Definition
| sized to match the the wire diameter |
|
|
Term
| What does the 70 indicate in the electrode classification ER70S-3 |
|
Definition
|
|
Term
| Excessive amounts of weld spatter in the nozzle may cause |
|
Definition
|
|
Term
| which of the following is not recommended when welding with short-circuiting |
|
Definition
|
|
Term
| which of the following is not an advantage of the GMAW process |
|
Definition
| good for use in windy areas |
|
|
Term
| The transfer mode that uses low currents, low voltage, and small diameter electrode wire to weld in all positions is called |
|
Definition
| short circuiting transfer |
|
|
Term
| what positions and types of welds can be successfully welded using the spray transfer mode on carbon steel? |
|
Definition
|
|
Term
| which of the shielding gas or gas mixture is most often used for welding carbon steel with the short-circuiting transfer mode? |
|
Definition
|
|
Term
|
Definition
|
|
Term
| Potential hazards related to arc welding are.. |
|
Definition
| radiation, fumes, toxic gases. |
|
|
Term
| when using a fire extinguisher to eliminate a fire it should be pointed to the |
|
Definition
|
|
Term
| What type of fire extingusher should be used on an electical fire |
|
Definition
|
|
Term
| What are the initials of the federal organization created to insure safe and sanitary working conditions for employees |
|
Definition
|
|
Term
| The maximum safe working pressure for Acetylene is |
|
Definition
|
|
Term
| Vaporized metals, such as zinc, cadmium, lead, chromium and berylllium |
|
Definition
|
|
Term
| Fuel gas hoses are usually colored |
|
Definition
|
|
Term
|
Definition
| a burn to the eye caused by exposure to ultriviolet light from the welding arc |
|
|
Term
| one should never enter a welding shop without wearing |
|
Definition
|
|
Term
| what should one never use on gas cylinders, regualtors, connections and hoses? |
|
Definition
|
|
Term
| one should never weld or cut directly against |
|
Definition
|
|
Term
| one should never operate arc welding euipment while |
|
Definition
| standing on wet or damp floors |
|
|
Term
| A burn that caused the skin to blister is referred to as a |
|
Definition
|
|
Term
| The selection of a corrext lens shade number depends on the |
|
Definition
| amount of welding current being used |
|
|
Term
| federal regualtion requires that hazardous information about a product be provided to all users of the product. The form used to provide this information is called a(n) |
|
Definition
| Material Safety Data Sheet (MSDS) |
|
|
Term
| Which of the following is the only acceptable method for lighing oxyfuel torches? |
|
Definition
|
|
Term
| Areas that have less then____ cubic feet per welder, or that have cielings less than 16ft high, require forced ventilation. |
|
Definition
|
|
Term
| A confined space is one that? |
|
Definition
| is large enough that a person can enter and perform tasks |
|
|
Term
|
Definition
| authorizes the performance of work potentially posing a fire hazard |
|
|
