Term
| What estimated percent of accidents are caused by nature? |
|
Definition
|
|
Term
In the operational risk management process, the responsibility for identifying and controlling
hazards rests with |
|
Definition
|
|
Term
Which safety-training phase is an effective tool that creates a lasting impression for new
airman |
|
Definition
|
|
Term
| Responsibility for initiating a lost tool report rests with the |
|
Definition
| person that was issued the tool. |
|
|
Term
| The lowest person authorized to clear a red X when a lost tool cannot be located is |
|
Definition
| an individual assigned to maintenance supervision |
|
|
Term
The pressure in a fire extinguisher is within a safe operating range when the gauge needle is
within the |
|
Definition
|
|
Term
| Minimum requirements for positioning of fire extinguishers is listed in |
|
Definition
|
|
Term
| Wearing dog tags, wristwatches, or other jewelry is expressly forbidden |
|
Definition
| when you’re working on electrical equipment. |
|
|
Term
Fall protection is required when it becomes necessary to perform required tasks where a
worker can fall |
|
Definition
|
|
Term
| Radiation hazards are affected by |
|
Definition
| strength of emission, time of exposure, and weather. |
|
|
Term
The recommended procedure for cooling an overheated brake assembly is to park the
aircraft in an isolated location, then |
|
Definition
| allow the assembly to cool in the ambient air. |
|
|
Term
| Normally, the safe distance behind an operating jet engine exhaust is |
|
Definition
|
|
Term
| How is a maintenance stand secured when placed near an operating propeller? |
|
Definition
| Wrap chains around each wheel individually. |
|
|
Term
| Which symptom is not a sign of noise fatigue? |
|
Definition
|
|
Term
| To ensure equipment is ready and available at the time of need, the Air Force uses |
|
Definition
|
|
Term
| Responsibility for establishing a climate that promotes maintenance discipline rests with |
|
Definition
|
|
Term
| Prime contributors to dropped objects are |
|
Definition
|
|
Term
| The objectives of the maintenance data documentation system include |
|
Definition
| collecting, storing, and retrieving base-level data. |
|
|
Term
| The basic rules for the maintenance data documentation system are contained in TO |
|
Definition
|
|
Term
| The three phases of the operational events subsystem of the IMDS CDB are |
|
Definition
| mission recording, mission accomplishment, and analysis. |
|
|
Term
| You can use the IMDS CDB Training Management Subsystem to monitor |
|
Definition
|
|
Term
After student graduation, how many days later is the technical school graduate assessment
survey normally sent out to organizations? |
|
Definition
|
|
Term
| Unsatisfactory comments on the graduate assessment survey are answered by |
|
Definition
| a telephone call from the instructor of the student |
|
|
Term
Tasks that a person is expected to perform in a duty position or workcenter but are not
included in the CFETP Part II or AFJQS are listed |
|
Definition
|
|
Term
| Who may standardize the arrangements of the forms binder? |
|
Definition
|
|
Term
To obtain billing information for fuel and oil on an aircraft, you would check the AFTO
Form |
|
Definition
|
|
Term
| When must the AFTO Form 781 be removed from the forms binder? |
|
Definition
| After the IMDS CDB event number is entered at maintenance debriefing |
|
|
Term
| Engine over-temperature conditions are recorded on the AFTO Form |
|
Definition
|
|
Term
| You would use the AFTO Form 781K to document |
|
Definition
|
|
Term
| The standards for the entries to be made in the AFTO 781 series forms are specified in the |
|
Definition
| 00–20 series of technical orders. |
|
|
Term
| Which is the proper way to manually record a date in the 781 series forms? |
|
Definition
|
|
Term
| What action is necessary to clear an erroneous red diagonal symbol? |
|
Definition
Place the statement “Symbol entered in error,” in the discrepancy block and sign the
“CORRECTED BY” block. |
|
|
Term
During an aircraft inspection, you find a deteriorated insignia decal. What symbol would
you use in the aircraft forms? |
|
Definition
|
|
Term
| How many Air Force TO catalogs are there? |
|
Definition
|
|
Term
| Inspection workcards are known as |
|
Definition
|
|
Term
Which TCTO is identified by a series of red diagonals alternately spaced with red Xs (/ X /
X / X) around the border of the first page? |
|
Definition
|
|
Term
| As a general rule, ITCTO are replaced by formal TOs within |
|
Definition
|
|
Term
| The procedures for the entries on an AFTO Form 22 are outlined in |
|
Definition
|
|
Term
| What type of TO improvement is issued for TCTO deficiencies? |
|
Definition
|
|
Term
| Which type of directive publication is an extension of an instruction? |
|
Definition
|
|
Term
| An example of something that should not be published in an OI would be |
|
Definition
| Installation traffic rules |
|
|
Term
| Publications are listed in AFIND2 in a |
|
Definition
1. Directive.
2. Nondirective |
|
|
Term
| A sequence chart used in aircraft maintenance best serves as |
|
Definition
| a ready reference for determining the progress of the inspection. |
|
|
Term
| Which inspection is basically a flight preparedness check? |
|
Definition
|
|
Term
What inspection is usually performed just prior to takeoff and may include operational
checks of some systems? |
|
Definition
|
|
Term
If a basic postflight inspection is not required, the thru-flight inspection is normally
performed |
|
Definition
| after the last flight of a specified flying period |
|
|
Term
| The basic postflight inspection is performed to |
|
Definition
| determine if the aircraft is suitable for another flight |
|
|
Term
| Which is the most extensive inspection? |
|
Definition
|
|
Term
| The home station check is accomplished in conjunction with |
|
Definition
| minor and major inspections. |
|
|
Term
What aircraft inspection requires skills, equipment, or facilities not normally possessed by
operating locations? |
|
Definition
| Programmed depot maintenance |
|
|
Term
What symbol is entered on the forms if an aircraft exceeds the programmed depot
maintenance cycle by 90 days and an extension is not granted? |
|
Definition
|
|
Term
| What type of inspection is used to ensure the completeness of historical documents? |
|
Definition
|
|
Term
Why are aluminum alloy washers used with steel bolts on aluminum alloy parts in lowtorque
applications? |
|
Definition
|
|
Term
| What bolt is used where heavy tension or lengthwise stress must be sustained? |
|
Definition
|
|
Term
| Which bolt has a recessed head and is used in high-tension applications? |
|
Definition
|
|
Term
At least how many threads must be showing through a self-locking nut for maximum
locking effect? |
|
Definition
|
|
Term
| To use .032 gauge safety wire properly, there should be how many turns per inch? |
|
Definition
|
|
Term
If the manufacture’s brochure is not available, prior to using a torque wrench, you should
cycle the torque wrench through the breakaway torque at the |
|
Definition
| maximum setting and at least six times |
|
|
Term
| Aircraft cable size is determined by its |
|
Definition
|
|
Term
|
Definition
| 7 wires with 19 strands per wire. |
|
|
Term
| Normally, pressure seals are constructed of |
|
Definition
|
|
Term
| To check the engagement of a push-pull rod end, you would |
|
Definition
| insert a piece of safety wire into the hole in the end of the terminal |
|
|
Term
| Aircraft tubing can be constructed of |
|
Definition
| aluminum-alloy and stainless-steel. |
|
|
Term
| Generally, low-pressure hoses are used for pressures of what pounds psi and below? |
|
Definition
|
|
Term
| What parts of a cannon plug complete the electrical circuit? |
|
Definition
|
|
Term
| What can you use to tighten cannon plugs? |
|
Definition
Fingers.
Strap wrench.
Padded conduit pliers. |
|
|
Term
| Corrosion or deterioration of a metal part continues until the part is |
|
Definition
|
|
Term
What is the most severe type of corrosion, because it’s hard to detect without some type of
nondestructive test? |
|
Definition
|
|
Term
| Which type of corrosion appears as corroded cracks in a metal? |
|
Definition
|
|
Term
| To reduce corrosion, what procedure do you follow when working on aerospace equipment? |
|
Definition
Do not mark on any metal structural component with a graphite pencil.
Do not degrade or scratch any surface unless it is an authorized procedure.
Do not use graphite as a lubricant for any component located in a high-heat area. |
|
|
Term
The optimum temperature used to cool sealants that were mixed in an automatic mixing
machine is |
|
Definition
|
|
Term
| What advantage is gained by using accelerators to speed up an adhesive curing process? |
|
Definition
| Air isn’t required to affect a cure. |
|
|
Term
| For the most part, the frequency of cleaning an aircraft exterior varies depending on the |
|
Definition
|
|
Term
What type of cleaners are not very effective on grease, but are excellent for lightly soiled
areas, plastics, and instrument glass covers in the interior of an aircraft? |
|
Definition
|
|
Term
What solution is used to treat areas that have been affected with electrolyte from a lead-acid
battery? |
|
Definition
| Sodium bicarbonate and water |
|
|
Term
| Which statement is not a good lubrication tip? |
|
Definition
| Heat lubricants to make them easier to apply |
|
|
Term
| Under ideal conditions, an aircraft is operationally ready when |
|
Definition
| the required inspection and servicing are complete |
|
|
Term
| Responsibility for accomplishing the –1 preflight check rests with |
|
Definition
|
|
Term
| Which condition is most likely to cause aircraft damage? |
|
Definition
|
|
Term
| What type of jack would you use to raise an aircraft strut prior to a tire change? |
|
Definition
|
|
Term
| The F–2 lifting bag is designed to lift |
|
Definition
| 24,000 pounds to a maximum height of 6 feet. |
|
|
Term
During crash recovery, what method of aircraft hoisting is confined to emergencies when no
other method is available? |
|
Definition
|
|
Term
| Bench stock levels are established to provide a |
|
Definition
|
|
Term
The maintenance activities that have the option to develop and maintain quick reference
lists are those with how many or more aircraft of the same mission, design, and series? |
|
Definition
|
|
Term
| To issue an item of equipment for short specified periods, use the |
|
Definition
|
|
Term
| Critical items are generally small numbers of items that cause the largest number of |
|
Definition
|
|
Term
| The base critical items list is maintained by |
|
Definition
| personnel in Base Supply in coordination with MSL |
|
|
Term
| Internal control of repairable items within maintenance is accomplished through the use of |
|
Definition
|
|
Term
What copy of the DD Form 1348–1 is retained by the individual who receives an item from
supply? |
|
Definition
|
|
Term
| What form is used to report accomplishment of TCTO? |
|
Definition
|
|
Term
| Red margins and letters are used to allow you to easily identify the DD Form |
|
Definition
|
|
Term
| Green margins and letters are used to allow you to easily identify the DD Form |
|
Definition
|
|
Term
| To report quality deficiencies attributed to errors in workmanship, use a Category |
|
Definition
|
|
Term
| Submission of a Category II deficiency report is required within how many calendar days? |
|
Definition
|
|
Term
| Engines overhauled by depot are covered against defects in workmanship for the first |
|
Definition
| 100 hours of operation or six months from the date of receipt |
|
|
Term
| A commander assures that property is receiving proper care and is being properly |
|
Definition
| making frequent visits to base activities. |
|
|
Term
What type of responsibility is assumed by an individual who has acquired physical
possession of government property? |
|
Definition
|
|
Term
When pecuniary liability is not involved, an individual may be relieved of property
responsibility |
|
Definition
| by turn-in or by transfer. |
|
|
